| Author |
Message |
|
zone11
|
Post subject: MEMS 1.3 Support  Posted: Mon Jun 06, 2016 11:44 0 am |
|
Joined:
Sun May 22, 2016 6:16 0 pm
Posts:
15
|
|
Are there any plans to support MEMS 1.3?
I have a MINI SPI here with MEMS 1.3 (2 Plug) ECU doing nasty things..
|
|
|
|
 |
|
pscan.eu
|
Post subject: Re: MEMS 1.3 Support Posted: Tue Jun 07, 2016 10:28 0 am |
|
Gold Trader
|
 |
Joined:
Wed Jun 04, 2014 8:14 0 pm
Posts:
480
|
|
|
|
|
|
|
Iseman
|
Post subject: Re: MEMS 1.3 Support Posted: Tue Jun 07, 2016 10:58 0 am |
|
Joined:
Thu Mar 24, 2016 7:39 0 am
Posts:
11
|
|
ECU Looks like a MEMS 1.6 but with two plugs at the ECU instead of one and it has a different number - e.g. MNE10027E. Diagnostic plug is three pin SPI plug which is also used for the MEMS 1.6.
@Zone11: have you tried to use pscan with the MEMS1.3 in using the MEMS1.6 profile? I guess the welcome procdure between MEMS1.3 and MEMS1.6 should be the same. But then could be differences as for MEMS1.3 you´ll need a Microcheck (or a T* with Microcheck functions).
|
|
|
|
|
|
|
zone11
|
Post subject: Re: MEMS 1.3 Support Posted: Tue Jun 07, 2016 5:27 0 pm |
|
Joined:
Sun May 22, 2016 6:16 0 pm
Posts:
15
|
|
Its like Ismean alleady explained (thanks!) I know this 2 Port ECUs from the early SPi Minis without 5AS.
Let me check the year of the car with the documents.
I tried it with pscan MEMS 1.6 with no success. No communication with the ECU.
Unfortunately I don't have a microcheck or Tx to give it a try.
With a bit of luck I find my old French Facom Tester for SPi.
|
|
|
|
|
|
|
zone11
|
Post subject: Re: MEMS 1.3 Support Posted: Tue Jun 07, 2016 7:01 0 pm |
|
Joined:
Sun May 22, 2016 6:16 0 pm
Posts:
15
|
|
The Mini is a 1993 SPi
The ECU is MNE10097
|
|
|
|
|
|
|
pscan.eu
|
Post subject: Re: MEMS 1.3 Support Posted: Tue Jun 07, 2016 10:48 0 pm |
|
Gold Trader
|
|
Joined:
Wed Jun 04, 2014 8:14 0 pm
Posts:
480
|
|
|
|
|
|
|
zone11
|
Post subject: Re: MEMS 1.3 Support Posted: Tue Jun 21, 2016 3:45 0 pm |
|
Joined:
Sun May 22, 2016 6:16 0 pm
Posts:
15
|
Little update with a SUCCESS! After fixing the loom, communication with MEMS 1.3 works now perfect! My setup: MNE10097, ECU Identifier 38000305, no immobilizer Tested functions: Live Data, Read Errors, Clear Errors The only error code I can't delete is: 6: Fuel temperature sensor fault. But the MINI isn't equipped with such a sensor, so no problem at all. 
|
|
|
|
|
|
|
Iseman
|
Post subject: Re: MEMS 1.3 Support Posted: Sat Jul 02, 2016 10:47 0 am |
|
Joined:
Thu Mar 24, 2016 7:39 0 am
Posts:
11
|
|
Hier Chris,
Did you just Used the MEMS1.6 profile to get access to the MEMS1.3?
My spare device is since yesterday in the post for Philip...
Sebastian
|
|
|
|
|
|
|
zone11
|
Post subject: Re: MEMS 1.3 Support Posted: Mon Jul 04, 2016 5:10 0 am |
|
Joined:
Sun May 22, 2016 6:16 0 pm
Posts:
15
|
Yes, all done with the MEMS 1.6 profile. Very nice, so official MEMS 1.3 Support in the near future  - Christian
|
|
|
|
|
|
